图片名称

Solutions

Contact Us

图片名称
图片名称

National 24-hour service hotline

400-116-2629

Group Headquarters

Cell phone:18126505465

E-mail: webmaster@lcs-cert.com

Address: Shenzhen City, Baoan District, Shajing Street, Nga side of the school of Wei Juji Industrial Park, Building A 1 ~ 2 floor, Building C 3 floor

Glow wire

Simulate the high temperature and fire hazard caused by fault conditions inside the lighting fixture. For lighting appliances, there are usually three options: 650 ℃, 750 ℃, and 850 ℃

 

Glow Wire Test is an experimental method for evaluating the fire resistance of materials or components under high temperature conditions. It simulates the situation where high temperatures may occur inside the lighting fixture due to faults such as short circuits, overheating, etc., which could lead to a fire. Evaluate the fire resistance of the hot wire by heating it to a specific temperature (such as 650 ℃, 750 ℃, 850 ℃) and contacting it with the sample. The following is a detailed explanation of the hot wire test:

 

Test Principle
Heat the standard sized hot wire to the specified temperature (such as 650 ℃, 750 ℃, 850 ℃), and then expose it to the sample for a certain period of time to simulate the high-temperature environment under fault conditions. Evaluate the anti ignition performance of the sample by observing whether it is ignited, combustion time, flame spread, etc.

 

Test Standard
Common hot wire testing standards include:

IEC 60695-2-11: International Electrotechnical Commission standard, applicable to fire hazard assessment of electronic and electrical products.

GB/T 5169.10: Chinese National Standard, equivalent to IEC 60695-2-11.

UL 746A: Underwriters Laboratories standard for evaluating the flammability of plastic materials.

 

test equipment
Heating wire device:

Including hot wire (usually nickel chromium wire, diameter 4mm), heating device, and temperature control system.

Sample fixture:

Fix the sample to ensure it is in the correct position and angle.

Temperature measuring device:

Used for calibrating and monitoring the temperature of the heating wire.

Bottom layer:

Place a standard substrate (such as silk paper) underneath the sample to evaluate whether the drips have ignited.

 

Test steps
Sample preparation:

Prepare standard sized samples to ensure they represent actual usage conditions.

The sample needs to be pre treated under standard temperature and humidity conditions.

Calibration temperature:

Heat the hot wire to the specified temperature (such as 650 ℃, 750 ℃, 850 ℃) and calibrate it using a temperature measuring device.

Installation sample:

Fix the sample on the fixture to ensure it is in the required position for testing.

Apply hot wire:

Contact the hot wire with the surface of the sample, apply a specified pressure (such as 1N), and maintain it for a specified time (such as 30 seconds).

Observation record:

Observe whether the sample ignites, burning time, flame spread, and whether droplets ignite the underlying layer.

Record combustion behavior and related data.

Termination conditions:

When the combustion time of the sample exceeds the specified value or the flame spreads to a specific area, the test is terminated.

 

result evaluation
According to the test results, evaluating the fire resistance performance of materials usually includes the following indicators:

Burning time: The burning time of the sample after removing the hot wire.

Flame spread: Whether the flame spreads to other parts of the sample or ignites the underlying layer.

Dripping: Does the dripping ignite the underlying layer.

 

Test points
Temperature control: Ensure accurate and stable heating wire temperature.

Contact pressure: The applied pressure should meet the standard requirements (such as 1N).

Environmental control: Testing should be conducted under standard temperature and humidity conditions.

Safety protection: Harmful gases may be generated during the testing process, and ventilation equipment is required.

 

application
Lamp industry: Evaluate the fire resistance performance of lamp shells, internal insulation materials, etc. under high temperature conditions.

Electronic and electrical industry: testing the fire hazard of components such as circuit boards, connectors, switches, etc.

Automotive industry: Evaluating the fire resistance performance of materials in automotive electrical systems.

Through the hot wire test, the fire hazard of materials or components under high temperature conditions can be effectively evaluated, providing a basis for product design and safety certification.

6 individual

Large-scale experimental base

150 individual

Professional Lab

30 All kinds of

Analysis Method

8 million times

Testing/year